Is there supposed to be small snowflake crystals / microscopic paper tissue like stru

[bigunitny]

Is there supposed to be small snowflake crystals / microscopic paper tissue like structures in test propionate/test no ester blend?

After looking at my test propionate/TNE i find small crystal like strands in oil . Is this normal? No pip after injection no fever not feeling any infection after injection? I use a 21 gauge to withdraw is this ok?

Thank you

 

[Tazz]

is it dissolving from movement and reappearing or is it just floating around? never seen this and yes a 21g to draw is fine.

 

[cmb5017]

Sounds like it's crashing...heat it up

 

[Tazz]

Sounds like it's crashing...heat it up

that could be the case, how are you storing it? did you try warming up the gear ? it's most likely crystallizing

 

[bigunitny]

that could be the case, how are you storing it? did you try warming up the gear ? it's most likely crystallizing

Its under my sink in cabinet in my bathroom ? Why would it crash down there?

 

[bigunitny]

Sounds like it's crashing...heat it up

What is "crashing" ? How and why does this occur ? Its in a bathroom humidity might be issue but temp never exceeds 80deg

 

[RickRock]

It's just crashing a little. Put in a pan on the stove in water and heat it until it resuspends

Gear can crash no matter where or how you store it



(PM me for a price list for Biotech Labs and 10% discount)

 

[MarkD]

It's just crashing a little. Put in a pan on the stove in water and heat it until it resuspends

Gear can crash no matter where or how you store it



(PM me for a price list for Biotech Labs and 10% discount)

Spot on. Just heat it in a sauce pan or heating pad.

 

[bigunitny]

Ill put water in pan place gear in pan with rubber above water vial glass in water for how much time? And at what temperature should i boil water too ? Not being dumb but I am so I dont want to mess this up

 

[RickRock]

Ill put water in pan place gear in pan with rubber above water vial glass in water for how much time? And at what temperature should i boil water too ? Not being dumb but I am so I dont want to mess this up

You don't need to bring it to boil but the water will need to be pretty hot. Just slowly warm it and pull out your vial every couple minutes and check it. Once the crystals are gone you are good to go

(PM me for a price list for Biotech Labs and 10% discount)

 

[bigunitny]

You don't need to bring it to boil but the water will need to be pretty hot. Just slowly warm it and pull out your vial every couple minutes and check it. Once the crystals are gone you are good to go

(PM me for a price list for Biotech Labs and 10% discount)

Thanks rick good stuff ill work on it tonight

 

[bigunitny]

You don't need to bring it to boil but the water will need to be pretty hot. Just slowly warm it and pull out your vial every couple minutes and check it. Once the crystals are gone you are good to go

(PM me for a price list for Biotech Labs and 10% discount)

I have a baby bottle warmer can i put it in there for like 5 mins

 

[bigunitny]

If i heat up the vial and i still see small particles maybe the stopper broke into the oil i cant see why that would happen i use 21gauge to load .. Very dissapointed

 

[bigunitny]

Follow up just worked. All i needed was a little patience kept it dipped a lil bit longer n now all fuzzy shitty snowflakes are gone

 

[RickRock]

Follow up just worked. All i needed was a little patience kept it dipped a lil bit longer n now all fuzzy shitty snowflakes are gone

Yep, that's all you need to do is give it heat and time bud. Glad you got it taken care of

 

[Peacock]

That is common. You can take the needle off a syringe insert it in the vial, place the vial on a cookie sheet and heat in the oven for twenty minutes at 250 then remove and heat again for twenty minutes and that will remove those crystals.

 

[bigunitny]

Yep, that's all you need to do is give it heat and time bud. Glad you got it taken care of

If god forbid there is any small rubber from the top in the oil how dangerous would it be if it got into my body?

 

[RickRock]

If god forbid there is any small rubber from the top in the oil how dangerous would it be if it got into my body?

That wouldn't be good at all, so you certainly don't want to inject that. That shouldn't ever be an issue unless you are drawing with too big of a gauge. The bigger needles can potentially take little chunks out of the stopper. I don't recommend drawing with an 18 or 20g. I myself draw with a 22 and inject with a 25g and have never had an issue

 

[bigunitny]

That wouldn't be good at all, so you certainly don't want to inject that. That shouldn't ever be an issue unless you are drawing with too big of a gauge. The bigger needles can potentially take little chunks out of the stopper. I don't recommend drawing with an 18 or 20g. I myself draw with a 22 and inject with a 25g and have never had an issue

I use 21g to draw n 23 for glute /quad 25 for delt tri.. What i will do to be most certain its not stopper in the oil is use a 25 to draw i cant see how the stopper would suck through a 25 without clogging therefore im thinking ill only get oil that way ..

 

[RickRock]

I use 21g to draw n 23 for glute /quad 25 for delt tri.. What i will do to be most certain its not stopper in the oil is use a 25 to draw i cant see how the stopper would suck through a 25 without clogging therefore im thinking ill only get oil that way ..

Yes that's correct. I can't see a piece ever making it through a 25g needle. Don't overthink it and worry bro. It shouldn't be an issue for you at all