Pinning mistakes?

[JL14028]

Sometimes when I inject I have no pain, bumps, itching, or swelling.

MOST OF THE TIME...the next day I have a knot/bump....hurts like hell...gets itchy...eventually goes away.

I'm using a 3ml 23 gauge. 1 inch.

Yesterday I pinned the left delt with primo....no pain. Then pinned the right delt with test cyp. Today my right delt hurts like hell... Arm feels weak.

I'm Not blaming the gear. WHAT AM I DOING WRONG?

 

[dhfeggv]

You are stabbing yourself deep in the muscle, and it's not supposed to hurt?

Of course it's going to swell and hurt.

However, there is normal soreness, then there is excessive pip. As long as it isnt excruciating, it shouldn't be a problem. A bit of swelling and soreness is completely normal.

 

[JL14028]

You are stabbing yourself deep in the muscle, and it's not supposed to hurt?

Of course it's going to swell and hurt.

However, there is normal soreness, then there is excessive pip. As long as it isnt excruciating, it shouldn't be a problem. A bit of swelling and soreness is completely normal.

I didn't say it isn't going to hurt.

What I'm describing is excessive pain.

 

[Testdude63]

How long are you taking to inject?

Do you aspirate?

Clean the area with 70% alcohol prior and post pinning?

Clean the vials the same way?

Do you hold the pin as steady as possible whilst in the muscle?

How slowly do you withdraw the pin?

 

[PHURIOUS]

Where in the dealt are u injecting


PHURIOUS

 

[suraonyx23]

Try heating up your gear and using a 25g or better yet a slin pin for delts

Sent from my RCT6773W22B using Tapatalk

 

[JL14028]

How long are you taking to inject?

Do you aspirate?

Clean the area with 70% alcohol prior and post pinning?

Clean the vials the same way?

Do you hold the pin as steady as possible whilst in the muscle?

How slowly do you withdraw the pin?

I haven't been aspirating because i lose control with the plunger and start fishing around.

I always swab the bottle tops and injection site area .

I try to keep it steady but the plunger requires a lot of force .

I've been waiting a couple of seconds to withdraw and some oil /blood will drip out.

 

[JL14028]

Where in the dealt are u injecting


PHURIOUS

Three fingers down from shoulder joint and slightly rear do I don't hit the tendon.

 

[JL14028]

Try heating up your gear and using a 25g or better yet a slin pin for delts

Sent from my RCT6773W22B using Tapatalk

Heat as in run under warm water?

 

[Testdude63]

I haven't been aspirating because i lose control with the plunger and start fishing around.

I always swab the bottle tops and injection site area .

I try to keep it steady but the plunger requires a lot of force .

I've been waiting a couple of seconds to withdraw and some oil /blood will drip out.

Hmm, sounds like you are doing most things correctly.

I usually take about 20-30 seconds to fully disperse the oil per .5ml I am injecting. It takes about 1 minute or more when I'm blasting. I then withdraw a little bit and let it sit, a little bit more and let it sit, etc until it's fully out. Massage the area gently for like 30-45 seconds with alcohol after pinning. See if that helps.

 

[PHURIOUS]

Three fingers down from shoulder joint and slightly rear do I don't hit the tendon.

Its better to stay to the inner and u wont hit the biceps tendon. U are probly too close to the deltoid nerve and pissing it off


PHURIOUS

 

[TIN MAN]

Sometimes when I inject I have no pain, bumps, itching, or swelling.

MOST OF THE TIME...the next day I have a knot/bump....hurts like hell...gets itchy...eventually goes away.

I'm using a 3ml 23 gauge. 1 inch.

Yesterday I pinned the left delt with primo....no pain. Then pinned the right delt with test cyp. Today my right delt hurts like hell... Arm feels weak.

I'm Not blaming the gear. WHAT AM I DOING WRONG?

JL the only place I like to pin is quad muscles 25g x 1" https://www.youtube.com/watch?v=azF1FoepHuo

Or the wife pins the gluteal muscle 23 x 1 1/2 that's it for me no pain at all

 

[JL14028]

Hmm, sounds like you are doing most things correctly.

I usually take about 20-30 seconds to fully disperse the oil per .5ml I am injecting. It takes about 1 minute or more when I'm blasting. I then withdraw a little bit and let it sit, a little bit more and let it sit, etc until it's fully out. Massage the area gently for like 30-45 seconds with alcohol after pinning. See if that helps.

I'm gonna try it thanks !

 

[JL14028]

Its better to stay to the inner and u wont hit the biceps tendon. U are probly too close to the deltoid nerve and pissing it off


PHURIOUS

Yeah ....it's very very tender and the oil is probably pushing on it

 

[JL14028]

JL the only place I like to pin is quad muscles 25g x 1" https://www.youtube.com/watch?v=azF1FoepHuo

Or the wife pins the gluteal muscle 23 x 1 1/2 that's it for me no pain at all

I tried quad but felt like I ripped some stuff in there but I'm definitely gonna watch the vid and try again bud

 

[sixsixzero]

Hmm, sounds like you are doing most things correctly.

I usually take about 20-30 seconds to fully disperse the oil per .5ml I am injecting. It takes about 1 minute or more when I'm blasting. I then withdraw a little bit and let it sit, a little bit more and let it sit, etc until it's fully out. Massage the area gently for like 30-45 seconds with alcohol after pinning. See if that helps.

I agree here, seems like it takes a hour to get all mine out.

 

[bobhead]

How frequently are you pinning the same site?

 

[JL14028]

How frequently are you pinning the same site?

I've been alternating right glute left glute right shoulder left shoulder

 

[RickRock]

Why aren't you pinning the primo and test together at once?


(PM me for a price list for Biotech Labs and 10% discount)

 

[RickRock]

I've been alternating right glute left glute right shoulder left shoulder

How frequent are you pinning? Twice a week? Every other day?


(PM me for a price list for Biotech Labs and 10% discount)